BETTOSEAL HYBRID
BETTOSEAL HYBRID
One component, UV Resistant, Bitumen, Solvent and Isocyanate Free, Hybrid Polymer Based, Waterproofing Material
MATERIAL DESCRIPTION
BETTOSEAL HYBRID is a hybrid polymer based, single component, solvent-free, elastic liquid membrane with crack bridging properties, applied on many surfaces for waterproofing and protection purposes.
14 Kg Plastic Bucket
AREAS OF USE
• Indoor and outdoor, horizontal and vertical applications,
• Concrete, ceramics, wood, glass, polycarbonate sheets, GRP,
metal, stone, marble, tile, brick, particleboard, aerated concrete,
• For waterproofing chimney connections, wall and floor joints, rain
gutters,
• On balconies, terraces, roofs and roof gutters,
• At the joints of sandwich panels,
• Drinking water tanks and water pools,
• For repair purposes at joints of bituminous and slate membranes,
• In wet volume insulation,
• It is used for waterproofing on thermal insulation applications (PU
FOAM, EPS, XPS etc.).
APPLICATION METHOD
BETTOSEAL HYBRID is ready for use. Do not add water or any
solvent to dilute.
The product in its special aluminum packaging is stolen before use,
then the packaging is cut open from the corner with scissors and
poured onto the application surface and applied to the surface with
a brush, short pile roller or notched trowel. Application is done in 2
coats. It is recommended to apply the coats with the application
directions perpendicular to each other.
Large surfaces over 25-30 m2 or areas with risk of cracking should
be reinforced with geotextile fabric after the first coat application.
2nd layer application is made on geotextile fabric.
Waiting time between coats varies between 12-24 hours depending
on temperature and humidity. Masking tape is used to ensure that
the end points of the application surface are flat. The masking tape
should be removed after maximum 10 minutes.
In applications to be coated with ceramic tiles, quartz sand of 1 to
1.5 kg/m2 is sprinkled on the surface before the top coat membrane
application dries in order to make the surface rough.
The finished product should be protected against rain and
mechanical stress until it dries.
ADVANTAGES
• Single component, easy to apply, (brush, short pile roller, airless
gun, notched trowel)
• Primerless application on dry and damp surfaces,
• Excellent adhesion, crack bridging and high elasticity,
• Water vapor permeable, UV resistant and paintable,
• Excellent weather resistance, freeze-thaw resistance,
• Resistant to chemicals see table
• Environmentally friendly.
;
• Indoor and outdoor, horizontal and vertical applications,
• Concrete, ceramics, wood, glass, polycarbonate sheets, GRP,
metal, stone, marble, tile, brick, particleboard, aerated concrete,
• For waterproofing chimney connections, wall and floor joints, rain
gutters,
• On balconies, terraces, roofs and roof gutters,
• At the joints of sandwich panels,
• Drinking water tanks and water pools,
• For repair purposes at joints of bituminous and slate membranes,
• In wet volume insulation,
• It is used for waterproofing on thermal insulation applications (PU
FOAM, EPS, XPS etc.).
APPLICATION METHOD
BETTOSEAL HYBRID is ready for use. Do not add water or any
solvent to dilute.
The product in its special aluminum packaging is stolen before use,
then the packaging is cut open from the corner with scissors and
poured onto the application surface and applied to the surface with
a brush, short pile roller or notched trowel. Application is done in 2
coats. It is recommended to apply the coats with the application
directions perpendicular to each other.
Large surfaces over 25-30 m2 or areas with risk of cracking should
be reinforced with geotextile fabric after the first coat application.
2nd layer application is made on geotextile fabric.
Waiting time between coats varies between 12-24 hours depending
on temperature and humidity. Masking tape is used to ensure that
the end points of the application surface are flat. The masking tape
should be removed after maximum 10 minutes.
In applications to be coated with ceramic tiles, quartz sand of 1 to
1.5 kg/m2 is sprinkled on the surface before the top coat membrane
application dries in order to make the surface rough.
The finished product should be protected against rain and
mechanical stress until it dries.
ADVANTAGES
• Single component, easy to apply, (brush, short pile roller, airless
gun, notched trowel)
• Primerless application on dry and damp surfaces,
• Excellent adhesion, crack bridging and high elasticity,
• Water vapor permeable, UV resistant and paintable,
• Excellent weather resistance, freeze-thaw resistance,
• Resistant to chemicals see table
• Environmentally friendly.
;